Match List I with List II Choose the correct answer from the options given below:LIST I LIST II A. Single polarity positive voltage clipper circuit I. 
B. Negative clamping circuit II. 
C. Differentiator circuit III. 
D. Logarithmic Amplifier IV. 
A-I, B-II, C-IV, D-III
- Identify the type of each circuit from List I and match it with the corresponding image from List II.
- A. Single polarity positive voltage clipper circuit: This circuit is designed to remove or 'clip' the positive half of an input waveform, maintaining only the zero or negative half. Look for a circuit with diodes configured to clip positive voltages.
- B. Negative clamping circuit: This circuit shifts the entire input waveform negatively by a constant DC value. This usually involves a diode, capacitor, and a DC restoration. Look for a circuit configured for DC restoration or clamping.
- C. Differentiator circuit: This circuit outputs the derivative of the input signal, highlighting rapid changes in the signal. Look for a configuration with a capacitor at the input and a resistor in the feedback loop.
- D. Logarithmic Amplifier: This amplifier provides an output proportional to the logarithm of the input. Look for a circuit with diodes or transistors indicating logarithmic conversion.
By matching based on the characteristics and component configurations, we find the correct option to be:
Correct Answer: A-I, B-II, C-IV, D-III
Similar Questions
Assertion (A) : An Op-Amp is a direct coupled high gain amplifier.
Reason (R) : It consists of one or more differential amplifiers and usually followed by a level translator and push pull stage.
The input to a differentiator is –5 V. Its output will be
Match the following :
List – I List – II a. h-parameters i. O/P voltage varies as the slope of i/p voltage b. differentiator ii. Noise division c. half-wave rectifier iii. Function of a Q point d. integrator iv. series diode clipper Codes :
Assertion (A) : Op-Amp is used for sensor circuit.
Reason (R) : A small signal amplifier amplify weak measured signals.
Consider the following circuit, the switch S1 allows the output to switch between two ranges of amplitudes from 0-0.1 V and 0-1 V. Arrange these values of R1, R2 and R3 in increasing order.
(A) Value of R1
(B) Value of R2
(C) Value of R3Choose the most appropriate answer from the options given below :
The given operational amplifier circuit corresponds to which electronic circuit application ?
Statements in connection to Op-Amp applications are :
A. If we use a square wave generator followed by integrator circuit we get a triangular wave at the output
B. The logarithmic amplifier called a log-amplifier or a logger, is basically a current to voltage converter.
C.
is a first order high pass filter with voltage followerD. If we use a square wave generator followed by a clipping circuit then we get a saw-tooth wave generator.
Choose the correct answer from the options given below:
The correct flow in the basic block diagram of op-Amp is
A. Complementary symmetry push pull amplifier block.
B. Dual input unbalanced output differential amplifier block
C. Emitter follower with constant current source block
D. Dual-Input balanced output differential amplifier block
Choose the correct answer from the options given below :
Match the following :
List - I List - II a) 
i) 
b) 
ii) 
c) 
iii) 
d) 
iv) 
Codes :
\(\dfrac{d^{2}y}{dt^{2}}+y=0\) can be solved using an Operational Amplifier. Which one is preferred ?
Important Questions from Op-Amp and Its Applications
In the circuit shown below, $R$ is $1\text{ k}\Omega$ and $R_f$ is $10\text{ k}\Omega$. If $V_{\text{in}}$ is $100\text{ mV}$ and the op-amps have supply voltages of $\pm 15\text{ V}$, then $V_{\text{out}}$ is _______ V.
For IC 741 circuit shown below, the maximum input frequency above which the output will be distorted is ____________.
Assume that an op-amp 741 connected as a unit gain inverting amplifier is applied with an input change of 10 V. Determine the time taken for the output to change by 10 V. [Slew rate for op-amp 741 = 0.5 V/µs]
What is the value of output voltage $V_o$ in the given circuit? Assume op-amp to be ideal and MOSFET operating in saturation region.
In an ideal op-amp, the common mode gain is _____________.
