Question
The chute feed system is beneficial over the formation of lap due to ________.
This question was previously asked in
CUET PG 2026 Agri-Business Management Question Paper (25-Mar-2026) (Shift 2)
The correct answer is
direct feeding of fibres to carding
Chute Feed System Advantage Over Lap Formation
The primary benefit of a chute feed system compared to the traditional formation of lap method is its mechanism for delivering fibres directly to the subsequent process, primarily the carding machine.
- Direct Feeding: The chute feed system continuously and directly feeds a uniform stream of fibres into the carding machine.
- Lap Formation Process: This involves creating a large, compressed roll of fibres (lap) which is then fed into the card. This is a less direct and potentially less consistent method.
- Efficiency Gain: Direct feeding bypasses the lap formation step, simplifying the process and ensuring a more consistent fibre supply to the card. This consistency leads to better carding efficiency and improved yarn quality.
Therefore, the key advantage highlighted in the options is the direct feeding of fibres to carding.
Was this answer helpful?
Similar Questions
- Given below are two statements : one is labelled as Assertion (A) and the other is labelled as Reason (R).
Assertion (A) : The yarn strength depends on the level of twist given in the final stage of ring spinning.
Reason (R) : Twist helps in binding the fibres through lateral pressure exerted by outer layers of fibres on the fibres in the core.
In the light of the above statements, choose the most appropriate answer from the options given below : - Given below are two statements : one is labelled as Assertion (A) and the other is labelled as Reason (R).
Assertion (A) : The configuration and orientation of fibres in a yarn decides the uniformity of twisted yarn.
Reason (R) : The proper drafting in different stages of spinning changes the configuration and orientation of fibres.
In the light of the above statements, choose the most appropriate answer from the options given below : - Given below are two statements : one is labelled as Assertion (A) and the other is labelled as Reason (R).
Assertion (A) : The single thread tensile strength tester works on pendulum lever principle.
Reason (R) : The force acting on the specimen is directly proportional to the sine of the angle through which the pendulum is lifted from its vertical rest position.
In the light of the above statements, choose the most appropriate answer from the options given below : - Given below are two statements : one is labelled as Assertion (A) and the other is labelled as Reason (R).
Assertion (A) : Latch needles are self sufficient, no extra element is required for hook closure.
Reason (R) : When the needle moves up and down, the formed loop opens and closes the latch.
In the light of the above statements, choose the most appropriate answer from the options given below : - Given below are two statements : one is labelled as Assertion (A) and the other is labelled as Reason (R).
Assertion (A) : The uneven dyeing leads to the poor appearance in case of cotton fabric.
Reason (R) : The mature cotton fibres poses the problems in uniform dyeing.
In the light of the above statements, choose the most appropriate answer from the options given below : - Given below are two statements : one is labelled as Assertion (A) and the other is labelled as Reason (R).
Assertion (A) : Polyester does not require desizing before dyeing.
Reason (R) : Polyester contains natural waxes and pectins.
In the light of the above statements, choose the most appropriate answer from the options given below : - In the draw texturising machine, the passage of yarn is :
A. primary heater
B. secondary heater
C. winding unit
D. creel
E. friction unit
Choose the correct answer from the options given below : - The sequence of processes involved in the chemical processing is :
A. scouring
B. finishing
C. dyeing
D. desizing
E. bleaching
Choose the correct answer from the options given below : - Melt spinning involves the continuous process for the multi-filament yarn manufacturing follows the sequence as :
A. melting of chips
B. quenching
C. extrusion of melt
D. drying of chips
E. winding on the bobbin
Choose the correct answer from the options given below : - The sequence of warp preparation for weaving is :
A. warping
B. sizing
C. winding
D. drawing and denting in
E. weaving
Choose the correct answer from the options given below :
Important Questions from Miscellaneous
- Which of the following scheduler/schedulers is/are also called CPU scheduler ?
(A). Short Term Scheduler
(B). Long Term Scheduler
(C). Medium Term Scheduler
(D). Asymmetric Scheduler
Choose the correct answer from the options given below: - A situation where two or more processes are blocked, waiting for resources held by each other is called:
- External fragmentation occurs ________.
- Which disk scheduling algorithm looks for the track closest to the current head position?
- Which CPU scheduling algorithm prefers the process with the shortest burst time?
Need Expert Advice?
Upcoming Exams
GATE
February 06, 2027
Test Series
CUET
CUET PG Psychology (HUQP20) 2026 Mock Test Series
10 Tests
753 Attempts
3.7(14)
English
More Questions from CUET PG
