All Exams Test series for 1 year @ ₹349 only
Question

In-situ vane shear test is conducted to determine the shear strength of

The correct answer is

Cohesive soil

In-situ Vane Shear Test Application

The In-situ vane shear test is a widely recognized and effective field test employed in geotechnical engineering to assess the shear strength of particular soil types. This test offers significant advantages because it allows for the measurement of soil strength directly in its natural, undisturbed state. Maintaining the soil's original condition is vital for accurate design and analysis of foundations, embankments, and other civil engineering structures.

Vane Shear Test for Cohesive Soils

The primary use of the In-situ vane shear test is to determine the undrained shear strength of cohesive soils. This includes soft to medium clays and certain types of silts that exhibit cohesive properties. Cohesive soils are characterized by their ability to stick together due to inter-particle forces (like electrostatic attraction or capillary tension in pore water), unlike granular soils where frictional resistance is the dominant strength component.

  • Cohesive soil: This category primarily includes clays and, in some cases, silts that behave cohesively. The In-situ vane shear test is exceptionally well-suited for these soils. Their undrained shear strength, which is crucial for short-term stability analyses, is significantly influenced by their cohesive nature. The test effectively measures this cohesion by determining the torque required to cause failure within the soil mass.
  • Non-cohesive soil: Soils such as pure sands and gravels (often referred to as sandy soil) are classified as non-cohesive or granular soils. The In-situ vane shear test is generally not appropriate for these soil types. The strength of non-cohesive soils is primarily derived from internal friction between particles, and the vane mechanism is not designed to accurately quantify this frictional resistance. For granular soils, alternative field tests like the Standard Penetration Test (SPT) or the Cone Penetration Test (CPT) are typically preferred.
  • Silty soil: Silts can sometimes behave like granular soils, especially when dry or non-plastic. However, many silts, particularly when saturated, exhibit cohesive characteristics. If a silty soil displays significant cohesive properties, the vane shear test can be applied. Nevertheless, its reliability tends to decrease as the silt becomes more granular or sandy in nature.

Principle of the Vane Shear Test

During the test, a four-bladed vane, resembling a cross, is carefully pushed into the undisturbed soil. This can be done at the base of a borehole or directly from the ground surface. Once embedded, the vane is rotated at a slow, constant angular velocity. The maximum torque required to shear a cylindrical surface of soil around the vane is measured. This measured torque ($$T$$) is then used to calculate the undrained shear strength ($$c_u$$) of the soil using the following fundamental relationship:

$$T = c_u \cdot K_{vane}$$

Where:

  • $$T$$ represents the measured maximum torque.
  • $$c_u$$ denotes the undrained shear strength of the soil.
  • $$K_{vane}$$ is a constant specific to the vane's dimensions. For a typical cylindrical shear surface assumed by the vane, the constant can be expressed as:

$$c_u = \frac{T}{\pi \left( \frac{D^2 H}{2} + \frac{D^3}{6} \right)}$$

Here:

  • $$D$$ is the diameter of the vane.
  • $$H$$ is the height of the vane.

This test offers a swift and dependable estimation of the in-situ undrained shear strength for soft to medium clays and plastic silts. It is an indispensable tool in geotechnical investigations, as it directly quantifies the soil's resistance to shearing under undrained conditions. This information is critical for various engineering analyses, including the stability of embankments, the design of excavations, and the calculation of bearing capacity for shallow foundations in clayey ground.

Was this answer helpful?

Important Questions from Shear Strength

  1. For saturated soil, Skempton's pore pressure coefficient B is

  2. The failure plane in direct shear test is:-

  3. In tri-axial compression test, the length of specimen is kept about ________ its diameter.

  4. When drainage is permitted throughout the triaxial test, it is known as:

  5. The Mohr-Coulomb failure theory represents which of the following equation as the line that represents the failure envelope ?

Need Expert Advice?

Start Your Preparation with Prepp Mobile App

Download the app from Google Play & App Store
Download the app from Google Play & App Store
Prepp Mobile App