All Exams Test series for 1 year @ ₹349 only
Question

The design bending strength of a laterally unsupported beam is given by?

(1) βb \(\frac{{{z_p}{f_y}}}{{{\gamma _{mo}}}}\)

(2) β b Z p f bd

(3) β b Z p X LT \(\frac{{{f_y}}}{{{\gamma _{mo}}}}\)

(4) β b Z p \(\frac{{{f_{bd}}}}{{{\gamma _{mo}}}}\)

The correct answer is Only (2) and (3) are correct

Beam Bending Strength for Laterally Unsupported Sections

The design bending strength of a laterally unsupported beam is a critical parameter in structural steel design. It specifically addresses the capacity of a beam member to resist bending moments when its compression flange is not continuously supported, making it susceptible to a phenomenon known as lateral torsional buckling. Indian Standard Code IS 800:2007 provides the guidelines and formulas for calculating this design strength.

Design Bending Strength Formula

As per IS 800:2007, Clause 8.2.1.2, the design bending strength (\(M_d\)) of a laterally unsupported beam is given by the formula:

$M_d = \beta_b Z_p f_{bd}$

Where:

  • \(\beta_b\) is a factor that depends on the plastic section properties and the moment gradient across the unbraced length. For plastic and compact sections under uniform moment, \(\beta_b\) is typically taken as 1.0.
  • \(Z_p\) is the plastic section modulus of the cross-section. It represents the plastic moment capacity of the section.
  • \(f_{bd}\) is the design bending compressive stress. This stress value already incorporates the reduction due to lateral torsional buckling, which is a key consideration for laterally unsupported beams.

Understanding Design Bending Compressive Stress (\(f_{bd}\))

The design bending compressive stress (\(f_{bd}\)) is a crucial component of the design bending strength calculation. It is derived by considering the nominal yield stress of the steel and applying a reduction factor that accounts for lateral torsional buckling. The formula for \(f_{bd}\) is:

$f_{bd} = \chi_{LT} \frac{f_y}{\gamma_{m0}}$

Where:

  • \(\chi_{LT}\) is the buckling reduction factor due to lateral torsional buckling. This factor directly reduces the yield strength based on the beam's slenderness ratio and buckling characteristics.
  • \(f_y\) is the specified minimum yield stress of the steel material.
  • \(\gamma_{m0}\) is the partial safety factor for resistance governed by yielding. As per IS 800:2007, its value is 1.10.

Expanded Design Bending Strength Formula

By substituting the expression for \(f_{bd}\) into the primary design bending strength formula, we can express \(M_d\) in a more detailed form:

$M_d = \beta_b Z_p \chi_{LT} \frac{f_y}{\gamma_{m0}}$

This expanded formula explicitly shows the influence of the buckling reduction factor, the yield stress, and the partial safety factor on the overall design bending strength.

Analysis of the Given Options

Let's evaluate each option based on the standard formulas for the design bending strength of laterally unsupported beams:

Option Expression Analysis
(1) \(\beta_b \frac{{{z_p}{f_y}}{{\gamma_{mo}}}}\) This expression is dimensionally incorrect. The partial safety factor \(\gamma_{m0}\) is typically in the denominator to reduce the nominal strength to a design strength. Multiplying by \(\gamma_{m0}\) would incorrectly increase the strength. Thus, this option is incorrect.
(2) \(\beta_b Z_p f_{bd}\) This expression exactly matches the primary formula for the design bending strength (\(M_d\)) of a laterally unsupported beam as given in IS 800:2007. This is a correct representation.
(3) \(\beta_b Z_p \chi_{LT} \frac{{{f_y}}}{{{\gamma_{m0}}}}\) This expression represents the expanded form of the design bending strength formula (\(M_d\)) where \(f_{bd}\) has been substituted with its components. This formula is also consistent with IS 800:2007 and is a correct representation.
(4) \(\beta_b Z_p \frac{{{f_{bd}}}}{{{\gamma_{m0}}}}\) This expression is incorrect. The term \(f_{bd}\) itself is the design bending compressive stress, which already incorporates the effect of \(\gamma_{m0}\) (and \(\chi_{LT}\)). Dividing by \(\gamma_{m0}\) again would be redundant and lead to an incorrect (lower) strength value.

Conclusion on Correct Options

Based on a detailed analysis of the formulas provided in IS 800:2007 for the design bending strength of laterally unsupported beams, both option (2) and option (3) accurately represent the calculation. Option (2) presents the concise form using \(f_{bd}\), while option (3) provides the detailed breakdown of \(f_{bd}\).

Was this answer helpful?

Important Questions from Tension Member

  1. Maximum Slenderness ratio of a compression member carrying loads resulting from wind or seismic load provided the deformation of such members does not adversely effect the stress in any part of member-

  2. Which of the following failure is not a type of failure in tension members in steel structures?

  3. When the length of a tension member is too long:

  4. The allowable stress in axial tension is generally kept less if the thickness of the member is more than

  5. The shear lag effect in beam flanges is disregarded when the width of flange with outstand supported along one edge is less than or equal to (Here L0 is the length between points of zero moment in the span)

Need Expert Advice?

Start Your Preparation with Prepp Mobile App

Download the app from Google Play & App Store
Download the app from Google Play & App Store
Prepp Mobile App