In a proctor test, 1.8 kg of moist soil was filled in the mould (volume = 944 cc) after compaction. A soil sample weighting 23 g was taken from the mould and oven dried for 24 hours at a temperature of 110°C. The weight of the dry sample was found to be 20 g. The specific gravity of soil solids is G = 2.7. The theoretical maximum value of the dry unit weight of the soil at that water content is equal to _____
18.85 kN/m 3
This problem involves calculating the theoretical maximum dry unit weight of a soil sample based on data from a Proctor test. We are given the total weight and volume of the compacted moist soil, the weight of a small sample before and after drying, and the specific gravity of the soil solids. The theoretical maximum dry unit weight at a specific water content corresponds to the condition where there are zero air voids (i.e., the soil is fully saturated, S=100%).
The water content is calculated from the weights of the moist and dry soil sample.
The water content (w) is the ratio of the weight of water to the weight of soil solids, expressed as a decimal or percentage:
\(w = \frac{\text{Weight of water}}{\text{Weight of solids}} = \frac{3 \, \text{g}}{20 \, \text{g}} = 0.15\)
So, the water content is 0.15 or 15%.
The theoretical maximum dry unit weight at a given water content represents the densest state the soil can achieve at that water content if all the void space is filled with water (zero air voids, degree of saturation S = 1 or 100%). This is often referred to as the "zero air voids" or "saturation" line on a compaction curve.
The dry unit weight (\(\gamma_d\)) of a soil can be related to its specific gravity (G), water content (w), degree of saturation (S), and the unit weight of water (\(\gamma_w\)) by the formula:
\(\gamma_d = \frac{G \gamma_w}{1 + \frac{wG}{S}}\)
For the theoretical maximum dry unit weight at a given water content, the degree of saturation (S) is 1 (zero air voids). Substituting S=1 into the formula:
\(\gamma_{d,max} = \frac{G \gamma_w}{1 + wG}\)
Now, we plug in the known values: G = 2.7, w = 0.15, and \(\gamma_w = 9.81 \, \text{kN/m}^3\).
\(\gamma_{d,max} = \frac{2.7 \times 9.81 \, \text{kN/m}^3}{1 + (0.15 \times 2.7)}\)
First, calculate the term in the denominator:
\(0.15 \times 2.7 = 0.405\)
So the denominator is:
\(1 + 0.405 = 1.405\)
Now, calculate the numerator:
\(2.7 \times 9.81 = 26.487 \, \text{kN/m}^3\)
Finally, perform the division:
\(\gamma_{d,max} = \frac{26.487 \, \text{kN/m}^3}{1.405} \approx 18.8519 \, \text{kN/m}^3\)
The theoretical maximum value of the dry unit weight of the soil at the calculated water content (15%) is approximately 18.85 kN/m³.
Note: The information about the total moist soil filled in the mould and the mould volume (1.8 kg in 944 cc) allows you to calculate the actual dry unit weight achieved in the Proctor test compaction. However, this question specifically asks for the theoretical maximum dry unit weight at that water content, which is determined by the zero air voids line calculation using G and w.
In a standard proctor test, the water content (W 1) and maximum dry density (γ dmax) are related as
For standard compaction test done on soil, the mass of hammer and drop of the hammer are:
In a Compaction test, as the compaction effort is increased, the optimum moisture content_____.
The zero – air voids curve is non – linear owing to: