All Exams Test series for 1 year @ ₹349 only
Question

Assuming that there is no possibility of shear buckling in the web, the maximum reduction permitted by IS 800-2007 in the (low shear) design bending strength of a semi-compact steel section due to high shear is

The correct answer is

zero

Steel Section Design Bending Strength under High Shear

Understanding the behavior of steel sections, especially semi-compact sections, under combined bending and shear is crucial in structural design. The Indian Standard IS 800-2007, which is the code of practice for general construction in steel, provides specific guidelines for such scenarios.

IS 800-2007 Guidelines for Bending Strength

The question specifically asks about the maximum reduction permitted by IS 800-2007 in the design bending strength of a semi-compact steel section when subjected to high shear, with the important assumption that there is no possibility of shear buckling in the web.

Let's break down the key terms and their implications as per IS 800-2007:

  • Semi-compact steel section: These are sections where the extreme fibre in compression can reach yield stress, but local buckling would prevent the development of the full plastic moment resistance. Their design bending strength is typically based on the elastic section modulus ($Z_e$) or a modified plastic section modulus ($\beta_b Z_p$), usually $\beta_b = 1.0$ for plastic and compact sections, and $\beta_b = Z_e/Z_p$ for semi-compact sections.
  • Low shear design bending strength: This refers to the bending strength of the section when the applied shear force is low, meaning it does not significantly interact with or reduce the bending capacity.
  • High shear: According to IS 800-2007 (Clause 9.3.2.1), a section is considered to be under high shear if the factored applied shear force ($V$) exceeds 0.6 times the design shear strength ($V_d$). That is, $V > 0.6 V_d$.
  • No possibility of shear buckling in the web: This assumption simplifies the analysis by eliminating a potential failure mode, allowing us to focus solely on the interaction between bending and shear strength without considering web instability.

Reduction in Design Bending Strength Due to High Shear

IS 800-2007, Clause 9.3.2.2 addresses the reduction in design bending strength for members subjected to high shear. This clause primarily provides interaction equations for plastic and compact sections that are capable of developing their plastic moment capacity. For such sections, when the shear force is high ($V > 0.6 V_d$), the design bending strength ($M_d$) is reduced to $M_{dv}$, calculated using an interaction formula:

$$M_{dv} = M_d - \beta (M_d - M_{fd})$$

where:

  • $M_d$ is the design plastic resistance of the section without considering shear.
  • $M_{fd}$ is the design plastic resistance of the flange alone.
  • $\beta = \left(\frac{2V}{V_d} - 1\right)^2$ (This factor is applied if $V > 0.6 V_d$).

However, this reduction formula is specifically for sections that can achieve plastic moments (i.e., plastic and compact sections). For semi-compact sections, the design bending strength is already limited because they cannot develop the full plastic moment. Their bending capacity is determined based on the elastic section modulus, and the interaction with high shear is handled differently, or often, no direct reduction is applied to the already reduced semi-compact moment capacity due to shear alone, especially when web buckling is not a concern.

If the section is semi-compact, its design bending strength ($M_d$) is calculated based on its elastic properties and classification, not its full plastic capacity. The code implies that for semi-compact sections, the interaction rules for high shear, which cause a reduction from the plastic moment, do not lead to a further reduction from their already limited semi-compact bending capacity. In essence, the reduction due to high shear is relevant when the section is trying to achieve its full plastic capacity. Since a semi-compact section cannot achieve full plastic capacity, the concept of a further reduction from its "low shear design bending strength" due to high shear is typically considered to be zero under the given conditions.

Section Classification Behaviour in Bending Effect of High Shear (IS 800-2007)
Plastic Can form plastic hinge and develop full plastic moment. Reduction in bending strength ($M_d \rightarrow M_{dv}$) when $V > 0.6 V_d$.
Compact Can form plastic hinge and develop full plastic moment. Reduction in bending strength ($M_d \rightarrow M_{dv}$) when $V > 0.6 V_d$.
Semi-compact Can reach yield stress but local buckling prevents full plastic moment development. Design strength based on elastic properties. No direct reduction from its already limited "low shear design bending strength" if web buckling is prevented. The interaction formulas typically apply to sections capable of plastic hinge formation.
Slender Local buckling occurs before yield stress is reached. Not applicable for direct moment resistance as per plastic/compact theory.

Given that the section is semi-compact and there is no possibility of shear buckling in the web, the design bending strength, which is already limited, is not further reduced due to the presence of high shear according to the provisions of IS 800-2007. Therefore, the maximum reduction permitted is zero.

Was this answer helpful?

Important Questions from General Design Principles

  1. For inspection of welded joint, the method in which iron fillings are spread over the weld and it is then subjected to an electric current is known as:

  2. ISLC stands for:

  3. As per IS 800-1984, what will be the permissible axial tension for mild steel power driven rivets?

  4. Select the Indian rolled steel section for which depth and weight per meter is written as specification.

  5. When two members connected are placed end to end and additional cover plates are provided on both the sides of main plates, the joint is generally known as

Need Expert Advice?

Start Your Preparation with Prepp Mobile App

Download the app from Google Play & App Store
Download the app from Google Play & App Store
Prepp Mobile App