All Exams Test series for 1 year @ ₹349 only
Question

Select the correct statement related to water distribution pipe systems.

The correct answer is

Drain valves are provided at all the low points.

Understanding Water Distribution System Valves

Water distribution pipe systems require various types of valves for efficient operation, maintenance, and safety. These valves control flow, isolate sections, release trapped air, and allow for draining the system. Let's look at some key valves and their typical placements.

Sluice Valve Placement

Sluice valves, also known as gate valves, are primarily used to shut off or allow the flow of water in a pipeline. They are essential for isolating sections of the water distribution system during repairs, maintenance, or emergencies. It is crucial to install sluice valves at various points throughout the network, not just at the beginning. This allows operators to isolate specific sections without affecting the entire system.

Air Valve Location

Air valves are vital for releasing air that accumulates inside the pipeline. Air can enter the system through various means and tends to collect at the highest points (summits) of the pipeline profile. If air is not released, it can cause blockages, reduce flow efficiency, and lead to pressure surges. Therefore, air valves are installed at all the high points in the water distribution network.

Drain Valve Function and Placement

Drain valves, also called blow-off valves, are used to empty the pipeline. This is necessary for maintenance, repairs, cleaning (flushing out sediment), or when a section needs to be taken out of service. Water naturally flows downwards due to gravity, so the points where water will collect and can be effectively drained are the low points in the pipeline profile. Thus, drain valves are installed at all the low points in the water distribution system.

Analyzing Water Pipe System Statements

Let's evaluate the given statements related to water distribution pipe systems based on our understanding of valve functions and placements:

  • Statement 1: Sluice valves are provided only once, at the start of pipe system.
    This statement is incorrect. Sluice valves are placed at multiple locations in the distribution network to allow for sectional isolation.
  • Statement 2: Air valves are provided at all the low points.
    This statement is incorrect. Air tends to accumulate at high points, not low points. Air valves are placed at high points to release trapped air.
  • Statement 3: Drain valves are provided at all the high points.
    This statement is incorrect. Drain valves are used to empty the pipe, and water will naturally drain to the low points. Therefore, drain valves are placed at low points.
  • Statement 4: Drain valves are provided at all the low points.
    This statement is correct. Drain valves are strategically located at the low points of the pipeline profile to facilitate complete draining of water and removal of accumulated sediment.

Based on the analysis, the correct statement about water distribution pipe systems is that drain valves are provided at all the low points.

Water Distribution Valve Revision

Valve Type Primary Function Typical Placement
Sluice Valve (Gate Valve) Isolate sections, control flow At various strategic points along the network
Air Valve Release trapped air At all high points (summits)
Drain Valve (Blow-off Valve) Empty pipeline, remove sediment At all low points (valleys)

Additional Information on Pipe Systems

Besides these essential valves, water distribution pipe systems also include other components like check valves (prevent backflow), pressure relief valves (protect against excessive pressure), hydrants (for fire fighting and flushing), and meters (for measuring consumption). Proper design and placement of all these components are crucial for the reliable and efficient delivery of safe drinking water.

Was this answer helpful?

Important Questions from Distribution of Water

  1. The cast iron pipes:

  2. If Q is the total quantity of water required by a town per year in litres, and P is the population of the town, then the per capita demand of water will be:

  3. Which of the following is NOT a type of variation in demand?
  4. Which of the following IS -Code is used for the basic requirements for water supply, drainage and sanitation?

  5. According to Federal plumbing rules, the gallon to use in new toilets is

Need Expert Advice?

Start Your Preparation with Prepp Mobile App

Download the app from Google Play & App Store
Download the app from Google Play & App Store
Prepp Mobile App